is the max delay value specified in the associated
action definition minus 10%. If the action definition
doesn't have a max delay defined then there is no
default for this object and a value MUST be specified
prior to activating this entry when monitorMaxDelay(4)
is selected.
Note: The corresponding slapmPolicyMonitorControl
BITS setting, enableAggregateTraps(3), MUST be selected
in order for any notification relating to this entry to
potentially be generated."
::= { slapmPolicyMonitorEntry 16 }
slapmPolicyMonitorMinInRateNotAchieves OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times that a minimum transfer in rate
was not achieved."
::= { slapmPolicyMonitorEntry 17 }
slapmPolicyMonitorMaxInRateExceeds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times that a maximum transfer in rate
was exceeded."
::= { slapmPolicyMonitorEntry 18 }
slapmPolicyMonitorMaxDelayExceeds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times that a maximum delay in rate
was exceeded."
::= { slapmPolicyMonitorEntry 19 }
slapmPolicyMonitorMinOutRateNotAchieves OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times that a minimum transfer out rate
was not achieved."
::= { slapmPolicyMonitorEntry 20 }
slapmPolicyMonitorMaxOutRateExceeds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The number of times that a maximum transfer out rate
was exceeded."
::= { slapmPolicyMonitorEntry 21 }
slapmPolicyMonitorCurrentDelayRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The current delay rate for this entry. This is
calculated by taking the average of the TCP
round trip times for all associating
slapmSubcomponentTable entries within a interval."
::= { slapmPolicyMonitorEntry 22 }
slapmPolicyMonitorRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object allows entries to be created and deleted
in the slapmPolicyMonitorTable. An entry in this table
is deleted by setting this object to destroy(6).
Removal of a corresponding (same policy and traffic profile
names) slapmPolicyStatsEntry has the side effect of the
automatic deletion an entry in this table."
::= { slapmPolicyMonitorEntry 23 }
-- Subcomponent Table
slapmSubcomponentTable OBJECT-TYPE
SYNTAX SEQUENCE OF SlapmSubcomponentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines a table to provide information on the
individually components that are mapped to
a policy rule (or old traffic profile).
The indexing for this table is designed to support
the use of an SNMP GET-NEXT operation using only
the remote address and remote port as a way for
a management station to retrieve the table entries
relating to a particular client."
::= { slapmTableObjects 3 }
slapmSubcomponentEntry OBJECT-TYPE
SYNTAX SlapmSubcomponentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Describes a particular subcomponent entry. This
table does not have an OwnerIndex as
part of its indexing since this table's contents
is intended to span multiple users."
INDEX {
slapmSubcomponentRemAddress,
slapmSubcomponentRemPort,
slapmSubcomponentLocalAddress,
slapmSubcomponentLocalPort
}
::= { slapmSubcomponentTable 1 }
SlapmSubcomponentEntry ::=
SEQUENCE {
slapmSubcomponentRemAddress OCTET STRING,
slapmSubcomponentRemPort Integer32,
slapmSubcomponentLocalAddress OCTET STRING,
slapmSubcomponentLocalPort Integer32,
slapmSubcomponentProtocol INTEGER,
slapmSubcomponentSystemAddress OCTET STRING,
slapmSubcomponentPolicyName SlapmNameType,
slapmSubcomponentTrafficProfileName SlapmNameType,
slapmSubcomponentLastActivity DateAndTime,
slapmSubcomponentInOctets Counter32,
slapmSubcomponentOutOctets Counter32,
slapmSubcomponentTcpOutBufferedOctets Counter32,
slapmSubcomponentTcpInBufferedOctets Counter32,
slapmSubcomponentTcpReXmts Counter32,
slapmSubcomponentTcpRoundTripTime Integer32,
slapmSubcomponentTcpRoundTripVariance Integer32,
slapmSubcomponentInPdus Counter32,
slapmSubcomponentOutPdus Counter32,
slapmSubcomponentApplName SnmpAdminString,
slapmSubcomponentMonitorStatus SlapmStatus,
slapmSubcomponentMonitorIntTime DateAndTime,
slapmSubcomponentMonitorCurrentInRate Gauge32,
slapmSubcomponentMonitorCurrentOutRate Gauge32,
slapmSubcomponentPolicyRuleIndex Unsigned32
}
slapmSubcomponentRemAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0 | 4 | 16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicate the remote address of a subcomponent.
A remote address can be either an ipv4 address in which
case 4 octets are required or as an ipv6 address that
requires 16 octets. The value of this subidentifier
is a zero length octet string when this entry relates
to a UDP listener."
::= { slapmSubcomponentEntry 1 }
slapmSubcomponentRemPort OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicate the remote port of a subcomponent.
The value of this subidentifier
is 0 when this entry relates to a UDP listener."
::= { slapmSubcomponentEntry 2 }
slapmSubcomponentLocalAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(4 | 16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicate the local address of a subcomponent.
A local address can be either an ipv4 address in which
case 4 octets are required or as an ipv6 address that
requires 16 octets."
::= { slapmSubcomponentEntry 3 }
slapmSubcomponentLocalPort OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Indicate the local port of a subcomponent."
::= { slapmSubcomponentEntry 4 }
slapmSubcomponentProtocol OBJECT-TYPE
SYNTAX INTEGER {
udpListener(1),
tcpConnection(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicate the protocol in use that identifies the
type of subcomponent."
::= { slapmSubcomponentEntry 5 }
slapmSubcomponentSystemAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0 | 4 | 16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Address of a system that an Policy definition relates to.
A zero length octet string can be used to indicate that
only a single system is being represented.
Otherwise, the length of the octet string should be
4 for an ipv4 address and 16 for an ipv6 address."
::= { slapmSubcomponentEntry 6 }
slapmSubcomponentPolicyName OBJECT-TYPE
SYNTAX SlapmNameType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"Policy name that this entry relates to.
This object, along with slapmSubcomponentTrafficProfileName,
have been replaced with the use of an unsigned integer
index that is mapped to an slapmPolicyNameEntry to actually
identify policy naming."
::= { slapmSubcomponentEntry 7 }
slapmSubcomponentTrafficProfileName OBJECT-TYPE
SYNTAX SlapmNameType
MAX-ACCESS read-only
STATUS deprecated
DESCRIPTION
"The corresponding traffic profile name.
This object, along with slapmSubcomponentProfileName,
have been replaced with the use of an unsigned integer
index that is mapped to an slapmPolicyNameEntry to
actually identify policy naming."
::= { slapmSubcomponentEntry 8 }
slapmSubcomponentLastActivity OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The date and timestamp of when this entry was last used."
DEFVAL { '0000000000000000'H }
::= { slapmSubcomponentEntry 9 }
slapmSubcomponentInOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets received from IP for this
connection."
::= { slapmSubcomponentEntry 10 }
slapmSubcomponentOutOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets sent to IP for this connection."
::= { slapmSubcomponentEntry 11 }
slapmSubcomponentTcpOutBufferedOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of outgoing octets buffered. The value
of this object is zero when the entry is not
for a TCP connection."
::= { slapmSubcomponentEntry 12 }
slapmSubcomponentTcpInBufferedOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of incoming octets buffered. The value
of this object is zero when the entry is not
for a TCP connection."
::= { slapmSubcomponentEntry 13 }
slapmSubcomponentTcpReXmts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of retransmissions. The value
of this object is zero when the entry is not
for a TCP connection."
::= { slapmSubcomponentEntry 14 }
slapmSubcomponentTcpRoundTripTime OBJECT-TYPE
SYNTAX Integer32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time that has elapsed, measured in
milliseconds, from when the last TCP segment was
transmitted by the TCP Stack until the ACK was
received.
The value of this object is zero when the entry is not
for a TCP connection."
::= { slapmSubcomponentEntry 15 }
slapmSubcomponentTcpRoundTripVariance OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Round trip time variance.
The value of this object is zero when the entry is not
for a TCP connection."
::= { slapmSubcomponentEntry 16 }
slapmSubcomponentInPdus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of protocol related data units transferred
inbound:
slapmSubcomponentProtocol PDU Type
udpListener(1) UDP datagrams
tcpConnection(2) TCP segments"
::= { slapmSubcomponentEntry 17 }
slapmSubcomponentOutPdus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of protocol related data units transferred
outbound:
slapmSubcomponentProtocol PDU Type
udpListener(1) UDP datagrams
tcpConnection(2) TCP segments"
::= { slapmSubcomponentEntry 18 }
slapmSubcomponentApplName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The application name associated with this entry if known,
otherwise a zero-length octet string is returned as the
value of this object."
::= { slapmSubcomponentEntry 19 }
slapmSubcomponentMonitorStatus OBJECT-TYPE
SYNTAX SlapmStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object indicates when a monitored
value has exceeded a threshold or isn't meeting the
defined service level. Only the following SlapmStatus
BITS setting can be reported here:
monitorMinInRateNotAchieved(5),
monitorMaxInRateExceeded(6),
monitorMaxDelayExceeded(7),
monitorMinOutRateNotAchieved(8),
monitorMaxOutRateExceeded(9)
This object only has meaning when an corresponding
slapmPolicyMonitorEntry exists with the
slapmPolicyMonitorControl BITS setting
monitorSubcomponents(5) enabled."
::= { slapmSubcomponentEntry 20 }
slapmSubcomponentMonitorIntTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The timestamp for when the last interval ended.
This object only has meaning when an corresponding
slapmPRMonEntry (or old slapmPolicyMonitorEntry)
exists with the slapmPRMonControl (or
slapmPolicyMonitorControl) BITS setting
monitorSubcomponents(5) enabled. All of the
octets returned when monitoring is not in effect
must be zero."
DEFVAL { '0000000000000000'H }
::= { slapmSubcomponentEntry 21 }
slapmSubcomponentMonitorCurrentInRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kilobits per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Using the value of the corresponding
slapmPRMonInterval (or slapmPolicyMonitorInterval),
slapmSubcomponentStatsInOctets
is divided by slapmSubcomponentMonitorInterval to determine
the current in transfer rate.
This object only has meaning when an corresponding
slapmPRMonEntry (or slapmPolicyMonitorEntry)
exists with the slapmPRMonControl (or
slapmPolicyMonitorControl) BITS setting
monitorSubcomponents(5) enabled. The value of this
object is zero when monitoring is not in effect."
::= { slapmSubcomponentEntry 22 }
slapmSubcomponentMonitorCurrentOutRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kilobits per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Using the value of the corresponding slapmPRMonInterval (or
slapmPolicyMonitorInterva)l, slapmSubcomponentStatsOutOctets
is divided by slapmPRMonInterval (or
slapmPolicyMonitorInterval) to determine the
current out transfer rate.
This object only has meaning when an corresponding
slapmPRMonEntry (or slapmPolicyMonitorEntry) exists with
the slapmPRMonControl (or slapmPolicyMonitorControl)
BITS setting monitorSubcomponents(5) enabled. The value
of this object is zero when monitoring is not in effect."
::= { slapmSubcomponentEntry 23 }
slapmSubcomponentPolicyRuleIndex OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Points to an slapmPolicyNameEntry when combined with
slapmSubcomponentSystemAddress to indicate the
policy naming that relates to this entry.
A value of 0 for this object MUST be returned when
the corresponding slapmSubcomponentEntry has no
policy rule associated with it."
::= { slapmSubcomponentEntry 24 }
-- Table that maps an unsigned integer index to whatever
-- names a policy rule.
slapmPolicyNameTable OBJECT-TYPE
SYNTAX SEQUENCE OF SlapmPolicyNameEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Provides the mapping between a policy index as a
unsigned 32 bit integer and the unique name associated
with a policy rule."
::= { slapmTableObjects 4 }
slapmPolicyNameEntry OBJECT-TYPE
SYNTAX SlapmPolicyNameEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the slapmPolicyNameTable."
INDEX {
slapmPolicyNameSystemAddress,
slapmPolicyNameIndex
}
::= { slapmPolicyNameTable 1 }
SlapmPolicyNameEntry ::=
SEQUENCE {
slapmPolicyNameSystemAddress OCTET STRING,
slapmPolicyNameIndex Unsigned32,
slapmPolicyNameOfRule SlapmPolicyRuleName
}
slapmPolicyNameSystemAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0 | 4 | 16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of a system that an Policy rule definition relates
to. A zero length octet string must be used to indicate
that only a single system is being represented.
Otherwise, the length of the octet string must be
4 for an ipv4 address or 16 for an ipv6 address."
::= { slapmPolicyNameEntry 1 }
slapmPolicyNameIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..4294967295)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A locally arbitrary, but unique identifier associated
with this table entry. This value is not expected to
remain constant across reIPLs."
::= { slapmPolicyNameEntry 2 }
slapmPolicyNameOfRule OBJECT-TYPE
SYNTAX SlapmPolicyRuleName
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The unique name that identifies a policy rule definition."
::= { slapmPolicyNameEntry 3 }
-- Sla Performance Monitoring Policy Rule Statistics Table
slapmPolicyRuleStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF SlapmPolicyRuleStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Provides statistics on a per system and a per policy
rule basis."
::= { slapmTableObjects 5 }
slapmPolicyRuleStatsEntry OBJECT-TYPE
SYNTAX SlapmPolicyRuleStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the slapmPolicyRuleStatsTable.
This table defines a set of statistics that is kept
on a per system and per policy rule basis.
Entries in this table are not created or deleted via SNMP
but reflect the set of policy rule definitions known
at a system."
INDEX {
slapmPolicyNameSystemAddress,
slapmPolicyNameIndex
}
::= { slapmPolicyRuleStatsTable 1 }
SlapmPolicyRuleStatsEntry ::=
SEQUENCE {
slapmPolicyRuleStatsOperStatus INTEGER,
slapmPolicyRuleStatsActiveConns Gauge32,
slapmPolicyRuleStatsTotalConns Counter32,
slapmPolicyRuleStatsLActivated DateAndTime,
slapmPolicyRuleStatsLastMapping DateAndTime,
slapmPolicyRuleStatsInOctets Counter32,
slapmPolicyRuleStatsOutOctets Counter32,
slapmPolicyRuleStatsConnLimit Unsigned32,
slapmPolicyRuleStatsCountAccepts Counter32,
slapmPolicyRuleStatsCountDenies Counter32,
slapmPolicyRuleStatsInDiscards Counter32,
slapmPolicyRuleStatsOutDiscards Counter32,
slapmPolicyRuleStatsInPackets Counter32,
slapmPolicyRuleStatsOutPackets Counter32,
slapmPolicyRuleStatsInProOctets Counter32,
slapmPolicyRuleStatsOutProOctets Counter32,
slapmPolicyRuleStatsMinRate Unsigned32,
slapmPolicyRuleStatsMaxRate Unsigned32,
slapmPolicyRuleStatsMaxDelay Unsigned32,
slapmPolicyRuleStatsTotalRsvpFlows Counter32,
slapmPolicyRuleStatsActRsvpFlows Gauge32
}
slapmPolicyRuleStatsOperStatus OBJECT-TYPE
SYNTAX INTEGER {
inactive(1),
active(2),
deleteNeeded(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The state of a policy entry:
inactive(1) - An policy entry was either defined
by local system definition or
discovered via
a directory search but has not been
activated (not currently being used).
active(2) - Policy entry is being used to affect
traffic flows.
deleteNeeded(3) - Either though local implementation
dependent methods or by discovering
that the directory entry corresponding
to this table entry no longer
exists and slapmPolicyPurgeTime needs
to expire before attempting to remove
the corresponding slapmPolicyStatsEntry
and any dependent slapmPolicyMonitor
table entries.
Note: a policy rule in a state other than
active(2) is not being used to affect traffic flows."
::= { slapmPolicyRuleStatsEntry 1 }
slapmPolicyRuleStatsActiveConns OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of active TCP connections that are
affected by the corresponding policy entry."
::= { slapmPolicyRuleStatsEntry 2 }
slapmPolicyRuleStatsTotalConns OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of total TCP connections that are
affected by the corresponding policy entry."
::= { slapmPolicyRuleStatsEntry 3 }
slapmPolicyRuleStatsLActivated OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The timestamp for when the corresponding policy entry
was last activated. The value of this object serves as
the discontinuity event indicator when polling entries
in this table. The value of this object is updated on
transition of slapmPolicyRuleStatsOperStatus into the
active(2) state."
DEFVAL { '0000000000000000'H }
::= { slapmPolicyRuleStatsEntry 4 }
slapmPolicyRuleStatsLastMapping OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The timestamp for when the last time
that the associated policy entry was used."
DEFVAL { '0000000000000000'H }
::= { slapmPolicyRuleStatsEntry 5 }
slapmPolicyRuleStatsInOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets that was received by IP for an
entity that map to this entry."
::= { slapmPolicyRuleStatsEntry 6 }
slapmPolicyRuleStatsOutOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of octets that was transmitted by IP for an
entity that map to this entry."
::= { slapmPolicyRuleStatsEntry 7 }
slapmPolicyRuleStatsConnLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The limit for the number of active TCP connections that
are allowed for this policy definition. A value of zero
for this object implies that a connection limit has not
been specified."
::= { slapmPolicyRuleStatsEntry 8 }
slapmPolicyRuleStatsCountAccepts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter is incremented when a policy action's
Permission value is set to Accept and a session
(TCP connection) is accepted."
::= { slapmPolicyRuleStatsEntry 9 }
slapmPolicyRuleStatsCountDenies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter is incremented when a policy action's
Permission value is set to Deny and a session is denied,
or when a session (TCP connection) is rejected due to a
policy's connection limit (slapmPolicyRuleStatsConnectLimit)
being reached."
::= { slapmPolicyRuleStatsEntry 10 }
slapmPolicyRuleStatsInDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of in octets discarded.
This occurs when an error is detected. Examples of this
are buffer overflow, checksum error, or bad packet
format."
::= { slapmPolicyRuleStatsEntry 11 }
slapmPolicyRuleStatsOutDiscards OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of out octets discarded.
Examples of this are buffer overflow, checksum error, or
bad packet format."
::= { slapmPolicyRuleStatsEntry 12 }
slapmPolicyRuleStatsInPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of in packets received
that relate to this policy entry from IP."
::= { slapmPolicyRuleStatsEntry 13 }
slapmPolicyRuleStatsOutPackets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of out packets sent
by IP that relate to this policy entry."
::= { slapmPolicyRuleStatsEntry 14 }
slapmPolicyRuleStatsInProOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of in octets that are
determined to be within profile."
::= { slapmPolicyRuleStatsEntry 15 }
slapmPolicyRuleStatsOutProOctets OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of out octets that are
determined to be within profile."
::= { slapmPolicyRuleStatsEntry 16 }
slapmPolicyRuleStatsMinRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Kilobits per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum transfer rate defined for this entry."
::= { slapmPolicyRuleStatsEntry 17 }
slapmPolicyRuleStatsMaxRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "Kilobits per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum transfer rate defined for this entry."
::= { slapmPolicyRuleStatsEntry 18 }
slapmPolicyRuleStatsMaxDelay OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum delay defined for this entry."
::= { slapmPolicyRuleStatsEntry 19 }
slapmPolicyRuleStatsTotalRsvpFlows OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of RSVP flows that have be activated."
::= { slapmPolicyRuleStatsEntry 20 }
slapmPolicyRuleStatsActRsvpFlows OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current number of active RSVP flows."
::= { slapmPolicyRuleStatsEntry 21 }
-- SLA Performance Monitoring Policy Rule Monitor Table
slapmPRMonTable OBJECT-TYPE
SYNTAX SEQUENCE OF SlapmPRMonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Provides a method of monitoring policies and their
effect at a system."
::= { slapmTableObjects 6 }
slapmPRMonEntry OBJECT-TYPE
SYNTAX SlapmPRMonEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Defines an entry in the slapmPRMonTable. This
table defines which policies should be monitored on a
per policy rule basis.
An attempt to set any read-create object defined within an
slapmPRMonEntry while the value of slapmPRMonRowStatus is
active(1) will result in an inconsistentValue error."
INDEX {
slapmPRMonOwnerIndex,
slapmPRMonSystemAddress,
slapmPRMonIndex
}
::= { slapmPRMonTable 1 }
SlapmPRMonEntry ::=
SEQUENCE {
slapmPRMonOwnerIndex SnmpAdminString,
slapmPRMonSystemAddress OCTET STRING,
slapmPRMonIndex Unsigned32,
slapmPRMonControl BITS,
slapmPRMonStatus SlapmStatus,
slapmPRMonInterval Unsigned32,
slapmPRMonIntTime DateAndTime,
slapmPRMonCurrentInRate Gauge32,
slapmPRMonCurrentOutRate Gauge32,
slapmPRMonMinRateLow Unsigned32,
slapmPRMonMinRateHigh Unsigned32,
slapmPRMonMaxRateHigh Unsigned32,
slapmPRMonMaxRateLow Unsigned32,
slapmPRMonMaxDelayHigh Unsigned32,
slapmPRMonMaxDelayLow Unsigned32,
slapmPRMonMinInRateNotAchieves Counter32,
slapmPRMonMaxInRateExceeds Counter32,
slapmPRMonMaxDelayExceeds Counter32,
slapmPRMonMinOutRateNotAchieves Counter32,
slapmPRMonMaxOutRateExceeds Counter32,
slapmPRMonCurrentDelayRate Gauge32,
slapmPRMonRowStatus RowStatus
}
slapmPRMonOwnerIndex OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"To facilitate the provisioning of access control by a
security administrator using the View-Based Access
Control Model (RFC2575, VACM) for tables in which
multiple users may need to independently create or modify
entries, the initial index is used as an 'owner index'.
Such an initial index has a syntax of SnmpAdminString,
and can thus be trivially mapped to a securityName or
groupName as defined in VACM, in accordance with a
security policy.
All entries in that table belonging to a particular user
will have the same value for this initial index. For a
given user's entries in a particular table, the object
identifiers for the information in these entries will
have the same subidentifiers (except for the 'column'
subidentifier) up to the end of the encoded owner index.
To configure VACM to permit access to this portion of the
table, one would create vacmViewTreeFamilyTable entries
with the value of vacmViewTreeFamilySubtree including the
owner index portion, and vacmViewTreeFamilyMask
'wildcarding' the column subidentifier. More elaborate
configurations are possible."
::= { slapmPRMonEntry 1 }
slapmPRMonSystemAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE(0 | 4 | 16))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Address of a system that an Policy definition relates to.
A zero length octet string can be used to indicate that
only a single system is being represented.
Otherwise, the length of the octet string should be
4 for an ipv4 address and 16 for an ipv6 address."
::= { slapmPRMonEntry 2 }
slapmPRMonIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An slapmPolicyNameTable index, slapmPolicyNameIndex,
that points to the unique name associated with a
policy rule definition."
::= { slapmPRMonEntry 3 }
slapmPRMonControl OBJECT-TYPE
SYNTAX BITS {
monitorMinRate(0),
monitorMaxRate(1),
monitorMaxDelay(2),
enableAggregateTraps(3),
enableSubcomponentTraps(4),
monitorSubcomponents(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object determines the type and level
of monitoring that is applied to a policy rule. The
value of this object can't be changed once the table
entry that it is a part of is activated via a
slapmPRMonRowStatus transition to active state.
monitorMinRate(0) - Monitor minimum transfer rate.
monitorMaxRate(1) - Monitor maximum transfer rate.
monitorMaxDelay(2) - Monitor maximum delay.
enableAggregateTraps(3) - The enableAggregateTraps(3)
BITS setting enables notification generation
when monitoring a policy rule as an
aggregate using the values in the corresponding
slapmPRMonStatsEntry. By default this function
is not enabled.
enableSubcomponentTraps(4) - This BITS setting enables
notification generation when monitoring all
subcomponents that are mapped to an corresponding
slapmPRMonStatsEntry. By default this
function is not enabled.
monitorSubcomponents(5) - This BITS setting enables
monitoring of each subcomponent (typically a
TCP connection or UDP listener) individually."
DEFVAL { { monitorMinRate, monitorMaxRate,
monitorMaxDelay } }
::= { slapmPRMonEntry 4 }
slapmPRMonStatus OBJECT-TYPE
SYNTAX SlapmStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object indicates when a monitored
value has not meet a threshold or isn't meeting the
defined service level. The SlapmStatus TEXTUAL-CONVENTION
defines two levels of not meeting a threshold. The first
set:
slaMinInRateNotAchieved(0),
slaMaxInRateExceeded(1),
slaMaxDelayExceeded(2),
slaMinOutRateNotAchieved(3),
slaMaxOutRateExceeded(4)
are used to indicate when the SLA as an aggregate is
not meeting a threshold while the second set:
monitorMinInRateNotAchieved(5),
monitorMaxInRateExceeded(6),
monitorMaxDelayExceeded(7),
monitorMinOutRateNotAchieved(8),
monitorMaxOutRateExceeded(9)
indicate that at least one subcomponent is not meeting
a threshold."
::= { slapmPRMonEntry 5 }
slapmPRMonInterval OBJECT-TYPE
SYNTAX Unsigned32 (15..86400) -- 15 second min, 24 hour max
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The number of seconds that defines the sample period."
DEFVAL {20} -- 20 seconds
::= { slapmPRMonEntry 6 }
slapmPRMonIntTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The timestamp for when the last interval ended."
DEFVAL { '0000000000000000'H }
::= { slapmPRMonEntry 7 }
slapmPRMonCurrentInRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kilobits per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Using the value of the corresponding
slapmPRMonInterval, slapmPolicyRuleStatsInOctets
is sampled and then divided by slapmPRMonInterval
to determine the current in transfer rate."
::= { slapmPRMonEntry 8 }
slapmPRMonCurrentOutRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "kilobits per second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Using the value of the corresponding
slapmPolicyMonInterval, slapmPolicyRuleStatsOutOctets
is sampled and then divided by slapmPRMonInterval
to determine the current out transfer rate."
::= { slapmPRMonEntry 9 }
slapmPRMonMinRateLow OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kilobits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The threshold for generating a
slapmPolicyRuleMonNotOkay notification, signalling
that a monitored minimum transfer rate has not been meet.
A slapmPolicyRuleMonNotOkay notification is not
generated again for an slapmPRMonEntry until
the minimum transfer rate
exceeds slapmPRMonMinRateHigh (a
slapmPolicyRuleMonOkay notification is then transmitted)
and then fails below slapmPRMonMinRateLow. This
behavior reduces the slapmPolicyRuleMonNotOkay
notifications that are transmitted.
A value of zero for this object is returned when the
slapmPRMonControl monitorMinRate(0) is not
enabled. When enabled the default value for this object
is the min rate value specified in the associated
action definition minus 10%. If the action definition
doesn't have a min rate defined then there is no
default for this object and a value MUST be specified
prior to activating this entry when monitorMinRate(0)
is selected.
Note: The corresponding slapmPRMonControl
BITS setting, enableAggregateTraps(3), MUST be selected in
order for any notification relating to this entry to
potentially be generated."
::= { slapmPRMonEntry 10 }
slapmPRMonMinRateHigh OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kilobits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The threshold for generating a slapmPolicyRuleMonOkay
notification, signalling that a monitored minimum
transfer rate has increased to an acceptable level.
A value of zero for this object is returned when the
slapmPRMonControl monitorMinRate(0) is not
enabled. When enabled the default value for this object
is the min rate value specified in the associated
action definition plus 10%. If the action definition
doesn't have a min rate defined then there is no
default for this object and a value MUST be specified
prior to activating this entry when monitorMinRate(0)
is selected.
Note: The corresponding slapmPRMonControl
BITS setting, enableAggregateTraps(3), MUST be selected
in order for any notification relating to this entry to
potentially be generated."
::= { slapmPRMonEntry 11 }
slapmPRMonMaxRateHigh OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kilobits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The threshold for generating a
slapmPolicyRuleMonNotOkay notification, signalling
that a monitored maximum transfer rate has been exceeded.
A slapmPolicyRuleNotOkay notification is not
generated again for an slapmPRMonEntry until the
maximum transfer rate fails below
slapmPRMonMaxRateLow (a slapmPolicyRuleMonOkay
notification is then transmitted) and then raises above
slapmPRMonMaxRateHigh. This behavior reduces the
slapmPolicyRuleMonNotOkay notifications that are
transmitted.
A value of zero for this object is returned when the
slapmPRMonControl monitorMaxRate(1) is not
enabled. When enabled the default value for this object
is the max rate value specified in the associated
action definition plus 10%. If the action definition
doesn't have a max rate defined then there is no
default for this object and a value MUST be specified
prior to activating this entry when monitorMaxRate(1)
is selected.
Note: The corresponding slapmPRMonControl
BITS setting, enableAggregateTraps(3), MUST be selected in
order for any notification relating to this entry to
potentially be generated."
::= { slapmPRMonEntry 12 }
slapmPRMonMaxRateLow OBJECT-TYPE
SYNTAX Unsigned32
UNITS "kilobits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The threshold for generating a slapmPolicyRuleMonOkay
notification, signalling that a monitored maximum
transfer rate has fallen to an acceptable level.
A value of zero for this object is returned when the
slapmPRMonControl monitorMaxRate(1) is not
enabled. When enabled the default value for this object
is the max rate value specified in the associated
action definition minus 10%. If the action definition
doesn't have a max rate defined then there is no
default for this object and a value MUST be specified
prior to activating this entry when monitorMaxRate(1)
is selected.
Note: The corresponding slapmPRMonControl
BITS setting, enableAggregateTraps(3), MUST be selected in
order for any notification relating to this entry to
potentially be generated."
::= { slapmPRMonEntry 13 }
slapmPRMonMaxDelayHigh OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The threshold for generating a
slapmPolicyRuleMonNotOkay notification, signalling
that a monitored maximum delay rate has been exceeded.
A slapmPolicyRuleMonNotOkay notification is not
generated again for an slapmPRMonEntry until
the maximum delay rate falls below
slapmPRMonMaxDelayLow (a slapmPolicyRuleMonOkay
notification is then transmitted) and raises above
slapmPRMonMaxDelayHigh. This behavior reduces
the slapmPolicyRuleMonNotOkay notifications that are
transmitted.
A value of zero for this object is returned when the
slapmPRMonControl monitorMaxDelay(4) is not
enabled. When enabled the default value for this object
is the max delay value specified in the associated
action definition plus 10%. If the action definition
doesn't have a max delay defined then there is no
default for this object and a value MUST be specified
prior to activating this entry when monitorMaxDelay(4)
is selected.
Note: The corresponding slapmPRMonControl
BITS setting, enableAggregateTraps(3), MUST be selected
in order for any notification relating to this entry to
potentially be generated."
::= { slapmPRMonEntry 14 }
slapmPRMonMaxDelayLow OBJECT-TYPE
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The threshold for generating a slapmPolicyRuleMonOkay
notification, signalling that a monitored maximum delay
rate has fallen to an acceptable level.
A value of zero for this object is returned when the
slapmPRMonControl monitorMaxDelay(4) is not
enabled. When enabled the default value for this object
is the max delay value specified in the associated
action definition minus 10%. If the action definition
doesn't have a max delay defined then there is no
default for this object and a value MUST be specified
prior to activating this entry when monitorMaxDelay(4)
is selected.
Note: The corresponding slapmPRMonControl
BITS setting, enableAggregateTraps(3), MUST be selected
in order for any notification relating to this entry to
potentially be generated."
::= { slapmPRMonEntry 15 }
slapmPRMonMinInRateNotAchieves OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that a minimum transfer in rate
was not achieved."
::= { slapmPRMonEntry 16 }
slapmPRMonMaxInRateExceeds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that a maximum transfer in rate
was exceeded."
::= { slapmPRMonEntry 17 }
slapmPRMonMaxDelayExceeds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that a maximum delay in rate
was exceeded."
::= { slapmPRMonEntry 18 }
slapmPRMonMinOutRateNotAchieves OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that a minimum transfer out rate
was not achieved."
::= { slapmPRMonEntry 19 }
slapmPRMonMaxOutRateExceeds OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times that a maximum transfer out rate
was exceeded."
::= { slapmPRMonEntry 20 }
slapmPRMonCurrentDelayRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current delay rate for this entry. This is
calculated by taking the average of the TCP
round trip times for all associating
slapmSubcomponentTable entries within a interval."
::= { slapmPRMonEntry 21 }
slapmPRMonRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object allows entries to be created and deleted
in the slapmPRMonTable. An entry in this table
is deleted by setting this object to destroy(6).
Removal of an corresponding (same policy index)
slapmPolicyRuleStatsEntry has the side effect of the
automatic deletion an entry in this table.
Note that an attempt to set any read-create object
defined within an slapmPRMonEntry while the value
of slapmPRMonRowStatus is active(1) will result in
an inconsistentValue error."
::= { slapmPRMonEntry 22 }
-- Notifications
slapmMonitoredEventNotAchieved NOTIFICATION-TYPE
OBJECTS {
slapmPolicyMonitorIntTime,
slapmPolicyMonitorControl,
slapmPolicyMonitorStatus,
slapmPolicyMonitorStatus,
slapmPolicyMonitorCurrentInRate,
slapmPolicyMonitorCurrentOutRate,
slapmPolicyMonitorCurrentDelayRate
}
STATUS deprecated
DESCRIPTION
"This notification is generated when an monitored event
is not achieved with respect to threshold. This
applies only towards monitoring a policy traffic
profile as an aggregate via an associating
slapmPolicyStatsEntry. The value
of slapmPolicyMonitorControl can be examined to
determine what is being monitored. The first
slapmPolicyMonitorStatus value supplies the current
monitor status while the 2nd value supplies the
previous status.
Note: The corresponding slapmPolicyMonitorControl
BITS setting, enableAggregateTraps(3), MUST be
selected in order for this notification to
potentially be generated."
::= { slapmNotifications 1 }
slapmMonitoredEventOkay NOTIFICATION-TYPE
OBJECTS {
slapmPolicyMonitorIntTime,
slapmPolicyMonitorControl,
slapmPolicyMonitorStatus,
slapmPolicyMonitorStatus,
slapmPolicyMonitorCurrentInRate,
slapmPolicyMonitorCurrentOutRate,
slapmPolicyMonitorCurrentDelayRate
}
STATUS deprecated
DESCRIPTION
"This notification is generated when a monitored
event has improved to an acceptable level. This
applies only towards monitoring a policy traffic
profile as an aggregate via an associating
slapmPolicyStatsEntry. The value
of slapmPolicyMonitorControl can be examined to
determine what is being monitored. The first
slapmPolicyMonitorStatus value supplies the current
monitor status while the 2nd value supplies the
previous status.
Note: The corresponding slapmPolicyMonitorControl
BITS setting, enableAggregateTraps(3), MUST be
selected in order for this notification to
potentially be generated."
::= { slapmNotifications 2 }
slapmPolicyProfileDeleted NOTIFICATION-TYPE
OBJECTS {
slapmPolicyStatsActiveConns,
slapmPolicyStatsTotalConns,
slapmPolicyStatsFirstActivated,
slapmPolicyStatsLastMapping,
slapmPolicyStatsInOctets,
slapmPolicyStatsOutOctets,
slapmPolicyStatsConnectionLimit,
slapmPolicyStatsCountAccepts,
slapmPolicyStatsCountDenies,
slapmPolicyStatsInDiscards,
slapmPolicyStatsOutDiscards,
slapmPolicyStatsInPackets,
slapmPolicyStatsOutPackets,
slapmPolicyStatsInProfileOctets,
slapmPolicyStatsOutProfileOctets,
slapmPolicyStatsMinRate,
slapmPolicyStatsMaxRate,
slapmPolicyStatsMaxDelay
}
STATUS deprecated
DESCRIPTION
"A slapmPolicyDeleted notification is sent when a
slapmPolicyStatsEntry is deleted if the value of
slapmPolicyTrapEnable is enabled(1)."
::= { slapmNotifications 3 }
slapmPolicyMonitorDeleted NOTIFICATION-TYPE
OBJECTS {
slapmPolicyMonitorStatus,
slapmPolicyMonitorInterval,
slapmPolicyMonitorIntTime,
slapmPolicyMonitorCurrentInRate,
slapmPolicyMonitorCurrentOutRate,
slapmPolicyMonitorCurrentDelayRate,
slapmPolicyMonitorMinRateLow,
slapmPolicyMonitorMinRateHigh,
slapmPolicyMonitorMaxRateHigh,
slapmPolicyMonitorMaxRateLow,
slapmPolicyMonitorMaxDelayHigh,
slapmPolicyMonitorMaxDelayLow,
slapmPolicyMonitorMinInRateNotAchieves,
slapmPolicyMonitorMaxInRateExceeds,
slapmPolicyMonitorMaxDelayExceeds,
slapmPolicyMonitorMinOutRateNotAchieves,
slapmPolicyMonitorMaxOutRateExceeds
}
STATUS deprecated
DESCRIPTION
"A slapmPolicyMonitorDeleted notification is sent when a
slapmPolicyMonitorEntry is deleted if the value of
slapmPolicyTrapEnable is enabled(1)."
::= { slapmNotifications 4 }
slapmSubcomponentMonitoredEventNotAchieved NOTIFICATION-TYPE
OBJECTS {
slapmSubcomponentSystemAddress,
slapmSubcomponentPolicyName,
slapmSubcomponentTrafficProfileName,
slapmSubcomponentMonitorStatus,
slapmSubcomponentMonitorStatus,
slapmSubcomponentMonitorIntTime,
slapmSubcomponentMonitorCurrentInRate,
slapmSubcomponentMonitorCurrentOutRate,
slapmSubcomponentTcpRoundTripTime
}
STATUS deprecated
DESCRIPTION
"This notification is generated when a monitored value
does not achieved a threshold specification. This
applies only towards monitoring the individual components
of a policy traffic profile. The value of the
corresponding slapmPolicyMonitorControl can be examined
to determine what is being monitored. The first
slapmSubcomponentMonitorStatus value supplies the current
monitor status while the 2nd value supplies the
previous status.
Note: The corresponding slapmPolicyMonitorControl
BITS setting, enableSubcomponentTraps(4), MUST be selected
in order for this notification to potentially be generated."
::= { slapmNotifications 5 }
slapmSubcomponentMonitoredEventOkay NOTIFICATION-TYPE
OBJECTS {
slapmSubcomponentSystemAddress,
slapmSubcomponentPolicyName,
slapmSubcomponentTrafficProfileName,
slapmSubcomponentMonitorStatus,
slapmSubcomponentMonitorStatus,
slapmSubcomponentMonitorIntTime,
slapmSubcomponentMonitorCurrentInRate,
slapmSubcomponentMonitorCurrentOutRate,
slapmSubcomponentTcpRoundTripTime
}
STATUS deprecated
DESCRIPTION
"This notification is generated when a monitored value
has reached an acceptable level.
Note: The corresponding slapmPolicyMonitorControl
BITS setting, enableSubcomponentTraps(3), MUST be
selected in order for this notification to potentially
be generated."
::= { slapmNotifications 6 }
slapmPolicyRuleMonNotOkay NOTIFICATION-TYPE
OBJECTS {
slapmPRMonIntTime,
slapmPRMonControl,
slapmPRMonStatus,
slapmPRMonStatus,
slapmPRMonCurrentInRate,
slapmPRMonCurrentOutRate,
slapmPRMonCurrentDelayRate
}
STATUS current
DESCRIPTION
"This notification is generated when an monitored event
is not achieved with respect to a threshold. This
applies only towards monitoring a policy rule
as an aggregate via an associating
slapmPolicyRuleStatsEntry. The value
of slapmPRMonControl can be examined to
determine what is being monitored. The first
slapmPRMonStatus value supplies the current
monitor status while the 2nd value supplies the
previous status.
Note: The corresponding slapmPRMonControl
BITS setting, enableAggregateTraps(3), MUST be
selected in order for this notification to
potentially be generated."
::= { slapmNotifications 7 }
slapmPolicyRuleMonOkay NOTIFICATION-TYPE
OBJECTS {
slapmPRMonIntTime,
slapmPRMonControl,
slapmPRMonStatus,
slapmPRMonStatus,
slapmPRMonCurrentInRate,
slapmPRMonCurrentOutRate,
slapmPRMonCurrentDelayRate
}
STATUS current
DESCRIPTION
"This notification is generated when a monitored
event has improved to an acceptable level. This
applies only towards monitoring a policy rule
as an aggregate via an associating
slapmPolicyRuleStatsEntry. The value
of slapmPRMonControl can be examined to
determine what is being monitored. The first
slapmPRMonStatus value supplies the current
monitor status while the 2nd value supplies the
previous status.
Note: The corresponding slapmPRMonControl
BITS setting, enableAggregateTraps(3), MUST be
selected in order for this notification to
potentially be generated."
::= { slapmNotifications 8 }
slapmPolicyRuleDeleted NOTIFICATION-TYPE
OBJECTS {
slapmPolicyRuleStatsActiveConns,
slapmPolicyRuleStatsTotalConns,
slapmPolicyRuleStatsLActivated,
slapmPolicyRuleStatsLastMapping,
slapmPolicyRuleStatsInOctets,
slapmPolicyRuleStatsOutOctets,
slapmPolicyRuleStatsConnLimit,
slapmPolicyRuleStatsCountAccepts,
slapmPolicyRuleStatsCountDenies,
slapmPolicyRuleStatsInDiscards,
slapmPolicyRuleStatsOutDiscards,
slapmPolicyRuleStatsInPackets,