datagrams it receives from registered mobile nodes (Section 4.2.2).
2.3.2. Sequence Numbers and Rollover Handling
The sequence number in Agent Advertisements ranges from 0 to 0xffff.
After booting, an agent MUST use the number 0 for its first
advertisement. Each subsequent advertisement MUST use the sequence
number one greater, with the exception that the sequence number
0xffff MUST be followed by sequence number 256. In this way, mobile
nodes can distinguish a reduction in the sequence number that occurs
after a reboot from a reduction that results in rollover of the
sequence number after it attains the value 0xffff.
2.4. Mobile Node Considerations
Every mobile node MUST implement Agent Solicitation. Solicitations
SHOULD only be sent in the absence of Agent Advertisements and when a
care-of address has not been determined through a link-layer protocol
or other means. The mobile node uses the same procedures, defaults,
and constants for Agent Solicitation as specified for ICMP Router
Solicitation messages [10], except that the mobile node MAY solicit
more often than once every three seconds, and that a mobile node that
is currently not connected to any foreign agent MAY solicit more
times than MAX_SOLICITATIONS.
The rate at which a mobile node sends Solicitations MUST be limited
by the mobile node. The mobile node MAY send three initial
Solicitations at a maximum rate of one per second while searching for
an agent. After this, the rate at which Solicitations are sent MUST
be reduced so as to limit the overhead on the local link. Subsequent
Solicitations MUST be sent using a binary exponential backoff
mechanism, doubling the interval between consecutive Solicitations,
up to a maximum interval. The maximum interval SHOULD be chosen
appropriately based upon the characteristics of the media over which
the mobile node is soliciting. This maximum interval SHOULD be at
least one minute between Solicitations.
While still searching for an agent, the mobile node MUST NOT increase
the rate at which it sends Solicitations unless it has received a
positive indication that it has moved to a new link. After
successfully registering with an agent, the mobile node SHOULD also
increase the rate at which it will send Solicitations when it next
begins searching for a new agent with which to register. The
increased solicitation rate MAY revert to the maximum rate, but then
MUST be limited in the manner described above. In all cases, the
recommended solicitation intervals are nominal values. Mobile nodes
MUST randomize their solicitation times around these nominal values
as specified for ICMP Router Discovery [10].
Mobile nodes MUST process received Agent Advertisements. A mobile
node can distinguish an Agent Advertisement message from other uses
of the ICMP Router Advertisement message by examining the number of
advertised addresses and the IP Total Length field. When the IP
total length indicates that the ICMP message is longer than needed
for the number of advertised addresses, the remaining data is
interpreted as one or more Extensions. The presence of a Mobility
Agent Advertisement Extension identifies the advertisement as an
Agent Advertisement.
If there is more than one advertised address, the mobile node SHOULD
pick the first address for its initial registration attempt. If the
registration attempt fails with a status Code indicating rejection by
the foreign agent, the mobile node MAY retry the attempt with each
subsequent advertised address in turn.
When multiple methods of agent discovery are in use, the mobile node
SHOULD first attempt registration with agents including Mobility
Agent Advertisement Extensions in their advertisements, in preference
to those discovered by other means. This preference maximizes the
likelihood that the registration will be recognized, thereby
minimizing the number of registration attempts.
A mobile node MUST ignore reserved bits in Agent Advertisements, as
opposed to discarding such advertisements. In this way, new bits can
be defined later, without affecting the ability for mobile nodes to
use the advertisements even when the newly defined bits are not
understood.
2.4.1. Registration Required
When the mobile node receives an Agent Advertisement with the 'R' bit
set, the mobile node SHOULD register through the foreign agent, even
when the mobile node might be able to acquire its own co-located
care-of address. This feature is intended to allow sites to enforce
visiting policies (such as accounting) which require exchanges of
authorization.
If formerly reserved bits require some kind of monitoring/enforcement
at the foreign link, foreign agents implementing the new
specification for the formerly reserved bits can set the 'R' bit.
This has the effect of forcing the mobile node to register through
the foreign agent, so the foreign agent could then monitor/enforce
the policy.
2.4.2. Move Detection
Two primary mechanisms are provided for mobile nodes to detect when
they have moved from one subnet to another. Other mechanisms MAY
also be used. When the mobile node detects that it has moved, it
SHOULD register (Section 3) with a suitable care-of address on the
new foreign network. However, the mobile node MUST NOT register more
frequently than once per second on average, as specified in Section
3.6.3.
2.4.2.1. Algorithm 1
The first method of move detection is based upon the Lifetime field
within the main body of the ICMP Router Advertisement portion of the
Agent Advertisement. A mobile node SHOULD record the Lifetime
received in any Agent Advertisements, until that Lifetime expires.
If the mobile node fails to receive another advertisement from the
same agent within the specified Lifetime, it SHOULD assume that it
has lost contact with that agent. If the mobile node has previously
received an Agent Advertisement from another agent for which the
Lifetime field has not yet expired, the mobile node MAY immediately
attempt registration with that other agent. Otherwise, the mobile
node SHOULD attempt to discover a new agent with which to register.
2.4.2.2. Algorithm 2
The second method uses network prefixes. The Prefix-Lengths
Extension MAY be used in some cases by a mobile node to determine
whether or not a newly received Agent Advertisement was received on
the same subnet as the mobile node's current care-of address. If the
prefixes differ, the mobile node MAY assume that it has moved. If a
mobile node is currently using a foreign agent care-of address, the
mobile node SHOULD NOT use this method of move detection unless both
the current agent and the new agent include the Prefix-Lengths
Extension in their respective Agent Advertisements; if this Extension
is missing from one or both of the advertisements, this method of
move detection SHOULD NOT be used. Similarly, if a mobile node is
using a co-located care-of address, it SHOULD not use this method of
move detection unless the new agent includes the Prefix-Lengths
Extension in its Advertisement and the mobile node knows the network
prefix of its current co-located care-of address. On the expiration
of its current registration, if this method indicates that the mobile
node has moved, rather than re-registering with its current care-of
address, a mobile node MAY choose instead to register with a the
foreign agent sending the new Advertisement with the different
network prefix. The Agent Advertisement on which the new
registration is based MUST NOT have expired according to its Lifetime
field.
2.4.3. Returning Home
A mobile node can detect that it has returned to its home network
when it receives an Agent Advertisement from its own home agent. If
so, it SHOULD deregister with its home agent (Section 3). Before
attempting to deregister, the mobile node SHOULD configure its
routing table appropriately for its home network (Section 4.2.1). In
addition, if the home network is using ARP [36], the mobile node MUST
follow the procedures described in Section 4.6 with regard to ARP,
proxy ARP, and gratuitous ARP.
2.4.4. Sequence Numbers and Rollover Handling
If a mobile node detects two successive values of the sequence number
in the Agent Advertisements from the foreign agent with which it is
registered, the second of which is less than the first and inside the
range 0 to 255, the mobile node SHOULD register again. If the second
value is less than the first but is greater than or equal to 256, the
mobile node SHOULD assume that the sequence number has rolled over
past its maximum value (0xffff), and that reregistration is not
necessary (Section 2.3).
3. Registration
Mobile IP registration provides a flexible mechanism for mobile nodes
to communicate their current reachability information to their home
agent. It is the method by which mobile nodes:
- request forwarding services when visiting a foreign network,
- inform their home agent of their current care-of address,
- renew a registration which is due to expire, and/or
- deregister when they return home.
Registration messages exchange information between a mobile node,
(optionally) a foreign agent, and the home agent. Registration
creates or modifies a mobility binding at the home agent, associating
the mobile node's home address with its care-of address for the
specified Lifetime.
Several other (optional) capabilities are available through the
registration procedure, which enable a mobile node to:
- discover its home address, if the mobile node is not configured
with this information.
- maintain multiple simultaneous registrations, so that a copy of
each datagram will be tunneled to each active care-of address
- deregister specific care-of addresses while retaining other
mobility bindings, and
- discover the address of a home agent if the mobile node is not
configured with this information.
3.1. Registration Overview
Mobile IP defines two different registration procedures, one via a
foreign agent that relays the registration to the mobile node's home
agent, and one directly with the mobile node's home agent. The
following rules determine which of these two registration procedures
to use in any particular circumstance:
- If a mobile node is registering a foreign agent care-of
address, the mobile node MUST register via that foreign agent.
- If a mobile node is using a co-located care-of address, and
receives an Agent Advertisement from a foreign agent on the
link on which it is using this care-of address, the mobile node
SHOULD register via that foreign agent (or via another foreign
agent on this link) if the 'R' bit is set in the received Agent
Advertisement message.
- If a mobile node is otherwise using a co-located care-of
address, the mobile node MUST register directly with its home
agent.
- If a mobile node has returned to its home network and is
(de)registering with its home agent, the mobile node MUST
register directly with its home agent.
Both registration procedures involve the exchange of Registration
Request and Registration Reply messages (Sections 3.3 and 3.4). When
registering via a foreign agent, the registration procedure requires
the following four messages:
a) The mobile node sends a Registration Request to the prospective
foreign agent to begin the registration process.
b) The foreign agent processes the Registration Request and then
relays it to the home agent.
c) The home agent sends a Registration Reply to the foreign agent
to grant or deny the Request.
d) The foreign agent processes the Registration Reply and then
relays it to the mobile node to inform it of the disposition of
its Request.
When the mobile node instead registers directly with its home agent,
the registration procedure requires only the following two messages:
a) The mobile node sends a Registration Request to the home agent.
b) The home agent sends a Registration Reply to the mobile node,
granting or denying the Request.
The registration messages defined in Sections 3.3 and 3.4 use the
User Datagram Protocol (UDP) [37]. A nonzero UDP checksum SHOULD be
included in the header, and MUST be checked by the recipient. A zero
UDP checksum SHOULD be accepted by the recipient. The behavior of
the mobile node and the home agent with respect to their mutual
acceptance of packets with zero UDP checksums SHOULD be defined as
part of the mobility security association which exists between them.
3.2. Authentication
Each mobile node, foreign agent, and home agent MUST be able to
support a mobility security association for mobile entities, indexed
by their SPI and IP address. In the case of the mobile node, this
must be its Home Address. See Section 5.1 for requirements for
support of authentication algorithms. Registration messages between
a mobile node and its home agent MUST be authenticated with an
authorization-enabling extension, e.g. the Mobile-Home Authentication
Extension (Section 3.5.2). This extension MUST be the first
authentication extension; other foreign agent-specific extensions MAY
be added to the message after the mobile node computes the
authentication.
3.3. Registration Request
A mobile node registers with its home agent using a Registration
Request message so that its home agent can create or modify a
mobility binding for that mobile node (e.g., with a new lifetime).
The Request may be relayed to the home agent by the foreign agent
through which the mobile node is registering, or it may be sent
directly to the home agent in the case in which the mobile node is
registering a co-located care-of address.
IP fields:
Source Address Typically the interface address from which the
message is sent.
Destination Address Typically that of the foreign agent or the
home agent.
See Sections 3.6.1.1 and 3.7.2.2 for details. UDP fields:
Source Port variable
Destination Port 434
The UDP header is followed by the Mobile IP fields shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type |S|B|D|M|G|r|T|x| Lifetime |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Home Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Home Agent |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Care-of Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ Identification +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Extensions ...
+-+-+-+-+-+-+-+-
Type 1 (Registration Request)
S Simultaneous bindings. If the 'S' bit is set, the mobile
node is requesting that the home agent retain its prior
mobility bindings, as described in Section 3.6.1.2.
B Broadcast datagrams. If the 'B' bit is set, the mobile
node requests that the home agent tunnel to it any
broadcast datagrams that it receives on the home network,
as described in Section 4.3.
D Decapsulation by mobile node. If the 'D' bit is set, the
mobile node will itself decapsulate datagrams which are
sent to the care-of address. That is, the mobile node is
using a co-located care-of address.
M Minimal encapsulation. If the 'M' bit is set, the mobile
node requests that its home agent use minimal
encapsulation [34] for datagrams tunneled to the mobile
node.
G GRE encapsulation. If the 'G' bit is set, the mobile
node requests that its home agent use GRE encapsulation
[16] for datagrams tunneled to the mobile node.
r Sent as zero; ignored on reception. SHOULD NOT be
allocated for any other uses.
T Reverse Tunneling requested; see [27].
x Sent as zero; ignored on reception.
Lifetime
The number of seconds remaining before the registration
is considered expired. A value of zero indicates a
request for deregistration. A value of 0xffff indicates
infinity.
Home Address
The IP address of the mobile node.
Home Agent
The IP address of the mobile node's home agent.
Care-of Address
The IP address for the end of the tunnel.
Identification
A 64-bit number, constructed by the mobile node, used for
matching Registration Requests with Registration Replies,
and for protecting against replay attacks of registration
messages. See Sections 5.4 and 5.7.
Extensions
The fixed portion of the Registration Request is followed
by one or more of the Extensions listed in Section 3.5.
An authorization-enabling extension MUST be included in
all Registration Requests. See Sections 3.6.1.3 and
3.7.2.2 for information on the relative order in which
different extensions, when present, MUST be placed in a
Registration Request message.
3.4. Registration Reply
A mobility agent returns a Registration Reply message to a mobile
node which has sent a Registration Request (Section 3.3) message. If
the mobile node is requesting service from a foreign agent, that
foreign agent will receive the Reply from the home agent and
subsequently relay it to the mobile node. The Reply message contains
the necessary codes to inform the mobile node about the status of its
Request, along with the lifetime granted by the home agent, which MAY
be smaller than the original Request.
The foreign agent MUST NOT increase the Lifetime selected by the
mobile node in the Registration Request, since the Lifetime is
covered by an authentication extension which enables authorization by
the home agent. Such an extension contains authentication data which
cannot be correctly (re)computed by the foreign agent. The home
agent MUST NOT increase the Lifetime selected by the mobile node in
the Registration Request, since doing so could increase it beyond the
maximum Registration Lifetime allowed by the foreign agent. If the
Lifetime received in the Registration Reply is greater than that in
the Registration Request, the Lifetime in the Request MUST be used.
When the Lifetime received in the Registration Reply is less than
that in the Registration Request, the Lifetime in the Reply MUST be
used.
IP fields:
Source Address Typically copied from the destination address
of the Registration Request to which the
agent is replying. See Sections 3.7.2.3 and
3.8.3.1 for complete details.
Destination Address Copied from the source address of the
Registration Request to which the agent is
replying
UDP fields:
Source Port <variable>
Destination Port Copied from the source port of the
corresponding Registration Request (Section
3.7.1).
The UDP header is followed by the Mobile IP fields shown below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Lifetime |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Home Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Home Agent |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ Identification +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Extensions ...
+-+-+-+-+-+-+-+-
Type 3 (Registration Reply)
Code A value indicating the result of the Registration
Request. See below for a list of currently defined Code
values.
Lifetime
If the Code field indicates that the registration was
accepted, the Lifetime field is set to the number of
seconds remaining before the registration is considered
expired. A value of zero indicates that the mobile node
has been deregistered. A value of 0xffff indicates
infinity. If the Code field indicates that the
registration was denied, the contents of the Lifetime
field are unspecified and MUST be ignored on reception.
Home Address
The IP address of the mobile node.
Home Agent
The IP address of the mobile node's home agent.
Identification
A 64-bit number used for matching Registration Requests
with Registration Replies, and for protecting against
replay attacks of registration messages. The value is
based on the Identification field from the Registration
Request message from the mobile node, and on the style of
replay protection used in the security context between
the mobile node and its home agent (defined by the
mobility security association between them, and SPI value
in the authorization-enabling extension). See Sections
5.4 and 5.7.
Extensions
The fixed portion of the Registration Reply is followed
by one or more of the Extensions listed in Section 3.5.
An authorization-enabling extension MUST be included in
all Registration Replies returned by the home agent. See
Sections 3.7.2.2 and 3.8.3.3 for rules on placement of
extensions to Reply messages.
The following values are defined for use within the Code field.
Registration successful:
0 registration accepted
1 registration accepted, but simultaneous mobility
bindings unsupported
Registration denied by the foreign agent:
64 reason unspecified
65 administratively prohibited
66 insufficient resources
67 mobile node failed authentication
68 home agent failed authentication
69 requested Lifetime too long
70 poorly formed Request
71 poorly formed Reply
72 requested encapsulation unavailable
73 reserved and unavailable
77 invalid care-of address
78 registration timeout
80 home network unreachable (ICMP error received)
81 home agent host unreachable (ICMP error received)
82 home agent port unreachable (ICMP error received)
88 home agent unreachable (other ICMP error received)
Registration denied by the home agent:
128 reason unspecified
129 administratively prohibited
130 insufficient resources
131 mobile node failed authentication
132 foreign agent failed authentication
133 registration Identification mismatch
134 poorly formed Request
135 too many simultaneous mobility bindings
136 unknown home agent address
Up-to-date values of the Code field are specified in the most recent
"Assigned Numbers" [40].
3.5. Registration Extensions
3.5.1. Computing Authentication Extension Values
The Authenticator value computed for each authentication Extension
MUST protect the following fields from the registration message:
- the UDP payload (that is, the Registration Request or
Registration Reply data),
- all prior Extensions in their entirety, and
- the Type, Length, and SPI of this Extension.
The default authentication algorithm uses HMAC-MD5 [23] to compute a
128-bit "message digest" of the registration message. The data over
which the HMAC is computed is defined as:
- the UDP payload (that is, the Registration Request or
Registration Reply data),
- all prior Extensions in their entirety, and
- the Type, Length, and SPI of this Extension.
Note that the Authenticator field itself and the UDP header are NOT
included in the computation of the default Authenticator value. See
Section 5.1 for information about support requirements for message
authentication codes, which are to be used with the various
authentication Extensions.
The Security Parameter Index (SPI) within any of the authentication
Extensions defines the security context which is used to compute the
Authenticator value and which MUST be used by the receiver to check
that value. In particular, the SPI selects the authentication
algorithm and mode (Section 5.1) and secret (a shared key, or
appropriate public/private key pair) used in computing the
Authenticator. In order to ensure interoperability between different
implementations of the Mobile IP protocol, an implementation MUST be
able to associate any SPI value with any authentication algorithm and
mode which it implements. In addition, all implementations of Mobile
IP MUST implement the default authentication algorithm (HMAC-MD5)
specified above.
3.5.2. Mobile-Home Authentication Extension
Exactly one authorization-enabling extension MUST be present in all
Registration Requests, and also in all Registration Replies generated
by the Home Agent. The Mobile-Home Authentication Extension is
always an authorization-enabling for registration messages specified
in this document. This requirement is intended to eliminate problems
[2] which result from the uncontrolled propagation of remote
redirects in the Internet. The location of the extension marks the
end of the authenticated data.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | SPI ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... SPI (cont.) | Authenticator ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type 32
Length 4 plus the number of bytes in the Authenticator.
SPI Security Parameter Index (4 bytes). An opaque
identifier (see Section 1.6).
Authenticator (variable length) (See Section 3.5.1.)
3.5.3. Mobile-Foreign Authentication Extension
This Extension MAY be included in Registration Requests and Replies
in cases in which a mobility security association exists between the
mobile node and the foreign agent. See Section 5.1 for information
about support requirements for message authentication codes.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | SPI ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... SPI (cont.) | Authenticator ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type 33
Length 4 plus the number of bytes in the Authenticator.
SPI Security Parameter Index (4 bytes). An opaque
identifier (see Section 1.6).
Authenticator (variable length) (See Section 3.5.1.)
3.5.4. Foreign-Home Authentication Extension
This Extension MAY be included in Registration Requests and Replies
in cases in which a mobility security association exists between the
foreign agent and the home agent. See Section 5.1 for information
about support requirements for message authentication codes.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | SPI ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... SPI (cont.) | Authenticator ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type 34
Length 4 plus the number of bytes in the Authenticator.
SPI Security Parameter Index (4 bytes). An opaque
identifier (see Section 1.6).
Authenticator (variable length) (See Section 3.5.1.)
3.6. Mobile Node Considerations
A mobile node MUST be configured with a netmask and a mobility
security association for each of its home agents. In addition, a
mobile node MAY be configured with its home address, and the IP
address of one or more of its home agents; otherwise, the mobile node
MAY discover a home agent using the procedures described in Section
3.6.1.2.
If the mobile node is not configured with a home address, it MAY use
the Mobile Node NAI extension [6] to identify itself, and set the
Home Address field of the Registration Request to 0.0.0.0. In this
case, the mobile node MUST be able to assign its home address after
extracting this information from the Registration Reply from the home
agent.
For each pending registration, the mobile node maintains the
following information:
- the link-layer address of the foreign agent to which the
Registration Request was sent, if applicable,
- the IP destination address of the Registration Request,
- the care-of address used in the registration,
- the Identification value sent in the registration,
- the originally requested Lifetime, and
- the remaining Lifetime of the pending registration.
A mobile node SHOULD initiate a registration whenever it detects a
change in its network connectivity. See Section 2.4.2 for methods by
which mobile nodes MAY make such a determination. When it is away
from home, the mobile node's Registration Request allows its home
agent to create or modify a mobility binding for it. When it is at
home, the mobile node's (de)Registration Request allows its home
agent to delete any previous mobility binding(s) for it. A mobile
node operates without the support of mobility functions when it is at
home.
There are other conditions under which the mobile node SHOULD
(re)register with its foreign agent, such as when the mobile node
detects that the foreign agent has rebooted (as specified in Section
2.4.4) and when the current registration's Lifetime is near
expiration.
In the absence of link-layer indications of changes in point of
attachment, Agent Advertisements from new agents SHOULD NOT cause a
mobile node to attempt a new registration, if its current
registration has not expired and it is still also receiving Agent
Advertisements from the foreign agent with which it is currently
registered. In the absence of link-layer indications, a mobile node
MUST NOT attempt to register more often than once per second.
A mobile node MAY register with a different agent when transport-
layer protocols indicate excessive retransmissions. A mobile node
MUST NOT consider reception of an ICMP Redirect from a foreign agent
that is currently providing service to it as reason to register with
a new foreign agent. Within these constraints, the mobile node MAY
register again at any time.
Appendix D shows some examples of how the fields in registration
messages would be set up in some typical registration scenarios.
3.6.1. Sending Registration Requests
The following sections specify details for the values the mobile node
MUST supply in the fields of Registration Request messages.
3.6.1.1. IP Fields
This section provides the specific rules by which mobile nodes pick
values for the IP header fields of a Registration Request.
IP Source Address:
- When registering on a foreign network with a co-located care-of
address, the IP source address MUST be the care-of address.
- Otherwise, if the mobile node does not have a home address, the
IP source address MUST be 0.0.0.0.
- In all other circumstances, the IP source address MUST be the
mobile node's home address.
IP Destination Address:
- When the mobile node has discovered the agent with which it is
registering, through some means (e.g., link-layer) that does
not provide the IP address of the agent (the IP address of the
agent is unknown to the mobile node), then the "All Mobility
Agents" multicast address (224.0.0.11) MUST be used. In this
case, the mobile node MUST use the agent's link-layer unicast
address in order to deliver the datagram to the correct agent.
- When registering with a foreign agent, the address of the agent
as learned from the IP source address of the corresponding
Agent Advertisement MUST be used. This MAY be an address which
does not appear as an advertised care-of address in the Agent
Advertisement. In addition, when transmitting this
Registration Request message, the mobile node MUST use a link-
layer destination address copied from the link-layer source
address of the Agent Advertisement message in which it learned
this foreign agent's IP address.
- When the mobile node is registering directly with its home
agent and knows the (unicast) IP address of its home agent, the
destination address MUST be set to this address.
- If the mobile node is registering directly with its home agent,
but does not know the IP address of its home agent, the mobile
node may use dynamic home agent address resolution to
automatically determine the IP address of its home agent
(Section 3.6.1.2). In this case, the IP destination address is
set to the subnet-directed broadcast address of the mobile
node's home network. This address MUST NOT be used as the
destination IP address if the mobile node is registering via a
foreign agent, although it MAY be used as the Home Agent
address in the body of the Registration Request when
registering via a foreign agent.
IP Time to Live:
- The IP TTL field MUST be set to 1 if the IP destination address
is set to the "All Mobility Agents" multicast address as
described above. Otherwise a suitable value should be chosen
in accordance with standard IP practice [38].
3.6.1.2. Registration Request Fields
This section provides specific rules by which mobile nodes pick
values for the fields within the fixed portion of a Registration
Request.
A mobile node MAY set the 'S' bit in order to request that the home
agent maintain prior mobility binding(s). Otherwise, the home agent
deletes any previous binding(s) and replaces them with the new
binding specified in the Registration Request. Multiple simultaneous
mobility bindings are likely to be useful when a mobile node using at
least one wireless network interface moves within wireless
transmission range of more than one foreign agent. IP explicitly
allows duplication of datagrams. When the home agent allows
simultaneous bindings, it will tunnel a separate copy of each
arriving datagram to each care-of address, and the mobile node will
receive multiple copies of datagrams destined to it.
The mobile node SHOULD set the 'D' bit if it is registering with a
co-located care-of address. Otherwise, the 'D' bit MUST NOT be set.
A mobile node MAY set the 'B' bit to request its home agent to
forward to it, a copy of broadcast datagrams received by its home
agent from the home network. The method used by the home agent to
forward broadcast datagrams depends on the type of care-of address
registered by the mobile node, as determined by the 'D' bit in the
mobile node's Registration Request:
- If the 'D' bit is set, then the mobile node has indicated that
it will decapsulate any datagrams tunneled to this care-of
address itself (the mobile node is using a co-located care-of
address). In this case, to forward such a received broadcast
datagram to the mobile node, the home agent MUST tunnel it to
this care-of address. The mobile node de-tunnels the received
datagram in the same way as any other datagram tunneled
directly to it.
- If the 'D' bit is NOT set, then the mobile node has indicated
that it is using a foreign agent care-of address, and that the
foreign agent will thus decapsulate arriving datagrams before
forwarding them to the mobile node. In this case, to forward
such a received broadcast datagram to the mobile node, the home
agent MUST first encapsulate the broadcast datagram in a
unicast datagram addressed to the mobile node's home address,
and then MUST tunnel this resulting datagram to the mobile
node's care-of address.
When decapsulated by the foreign agent, the inner datagram will
thus be a unicast IP datagram addressed to the mobile node,
identifying to the foreign agent the intended destination of
the encapsulated broadcast datagram, and will be delivered to
the mobile node in the same way as any tunneled datagram
arriving for the mobile node. The foreign agent MUST NOT
decapsulate the encapsulated broadcast datagram and MUST NOT
use a local network broadcast to transmit it to the mobile
node. The mobile node thus MUST decapsulate the encapsulated
broadcast datagram itself, and thus MUST NOT set the 'B' bit in
its Registration Request in this case unless it is capable of
decapsulating datagrams.
The mobile node MAY request alternative forms of encapsulation by
setting the 'M' bit and/or the 'G' bit, but only if the mobile node
is decapsulating its own datagrams (the mobile node is using a co-
located care-of address) or if its foreign agent has indicated
support for these forms of encapsulation by setting the corresponding
bits in the Mobility Agent Advertisement Extension of an Agent
Advertisement received by the mobile node. Otherwise, the mobile
node MUST NOT set these bits.
The Lifetime field is chosen as follows:
- If the mobile node is registering with a foreign agent, the
Lifetime SHOULD NOT exceed the value in the Registration
Lifetime field of the Agent Advertisement message received from
the foreign agent.
When the method by which the care-of address is learned does
not include a Lifetime, the default ICMP Router Advertisement
Lifetime (1800 seconds) MAY be used.
- The mobile node MAY ask a home agent to delete a particular
mobility binding, by sending a Registration Request with the
care-of address for this binding, with the Lifetime field set
to zero (Section 3.8.2).
- Similarly, a Lifetime of zero is used when the mobile node
deregisters all care-of addresses, such as upon returning home.
The Home Address field MUST be set to the mobile node's home address,
if this information is known. Otherwise, the Home Address MUST be
set to zeroes.
The Home Agent field MUST be set to the address of the mobile node's
home agent, if the mobile node knows this address. Otherwise, the
mobile node MAY use dynamic home agent address resolution to learn
the address of its home agent. In this case, the mobile node MUST
set the Home Agent field to the subnet-directed broadcast address of
the mobile node's home network. Each home agent receiving such a
Registration Request with a broadcast destination address MUST reject
the mobile node's registration and SHOULD return a rejection
Registration Reply indicating its unicast IP address for use by the
mobile node in a future registration attempt.
The Care-of Address field MUST be set to the value of the particular
care-of address that the mobile node wishes to (de)register. In the
special case in which a mobile node wishes to deregister all care-of
addresses, it MUST set this field to its home address.
The mobile node chooses the Identification field in accordance with
the style of replay protection it uses with its home agent. This is
part of the mobility security association the mobile node shares with
its home agent. See Section 5.7 for the method by which the mobile
node computes the Identification field.
3.6.1.3. Extensions
This section describes the ordering of any mandatory and any optional
Extensions that a mobile node appends to a Registration Request.
This following ordering MUST be followed:
a) The IP header, followed by the UDP header, followed by the
fixed-length portion of the Registration Request, followed by
b) If present, any non-authentication Extensions expected to be
used by the home agent (which may or may not also be useful to
the foreign agent), followed by
c) An authorization-enabling extension, followed by
d) If present, any non-authentication Extensions used only by the
foreign agent, followed by
e) The Mobile-Foreign Authentication Extension, if present.
Note that items (a) and (c) MUST appear in every Registration Request
sent by the mobile node. Items (b), (d), and (e) are optional.
However, item (e) MUST be included when the mobile node and the
foreign agent share a mobility security association.
3.6.2. Receiving Registration Replies
Registration Replies will be received by the mobile node in response
to its Registration Requests. Registration Replies generally fall
into three categories:
- the registration was accepted,
- the registration was denied by the foreign agent, or
- the registration was denied by the home agent.
The remainder of this section describes the Registration Reply
handling by a mobile node in each of these three categories.
3.6.2.1. Validity Checks
Registration Replies with an invalid, non-zero UDP checksum MUST be
silently discarded.
In addition, the low-order 32 bits of the Identification field in the
Registration Reply MUST be compared to the low-order 32 bits of the
Identification field in the most recent Registration Request sent to
the replying agent. If they do not match, the Reply MUST be silently
discarded.
Also, the Registration Reply MUST be checked for presence of an
authorization-enabling extension. For all Registration Reply
messages containing a Status Code indicating status from the Home
Agent, the mobile node MUST check for the presence of an
authorization-enabling extension, acting in accordance with the Code
field in the Reply. The rules are as follows:
a) If the mobile node and the foreign agent share a mobility
security association, exactly one Mobile-Foreign Authentication
Extension MUST be present in the Registration Reply, and the
mobile node MUST check the Authenticator value in the
Extension. If no Mobile-Foreign Authentication Extension is
found, or if more than one Mobile-Foreign Authentication
Extension is found, or if the Authenticator is invalid, the
mobile node MUST silently discard the Reply and SHOULD log the
event as a security exception.
b) If the Code field indicates that service is denied by the home
agent, or if the Code field indicates that the registration was
accepted by the home agent, exactly one Mobile-Home
Authentication Extension MUST be present in the Registration
Reply, and the mobile node MUST check the Authenticator value
in the Extension. If the Registration Reply was generated by
the home agent but no Mobile-Home Authentication Extension is
found, or if more than one Mobile-Home Authentication Extension
is found, or if the Authenticator is invalid, the mobile node
MUST silently discard the Reply and SHOULD log the event as a
security exception.
If the Code field indicates an authentication failure, either at the
foreign agent or the home agent, then it is quite possible that any
authenticators in the Registration Reply will also be in error. This
could happen, for example, if the shared secret between the mobile
node and home agent was erroneously configured. The mobile node
SHOULD log such errors as security exceptions.
3.6.2.2. Registration Request Accepted
If the Code field indicates that the request has been accepted, the
mobile node SHOULD configure its routing table appropriately for its
current point of attachment (Section 4.2.1).
If the mobile node is returning to its home network and that network
is one which implements ARP, the mobile node MUST follow the
procedures described in Section 4.6 with regard to ARP, proxy ARP,
and gratuitous ARP.
If the mobile node has registered on a foreign network, it SHOULD
re-register before the expiration of the Lifetime of its
registration. As described in Section 3.6, for each pending
Registration Request, the mobile node MUST maintain the remaining
lifetime of this pending registration, as well as the original
Lifetime from the Registration Request. When the mobile node
receives a valid Registration Reply, the mobile node MUST decrease
its view of the remaining lifetime of the registration by the amount
by which the home agent decreased the originally requested Lifetime.
This procedure is equivalent to the mobile node starting a timer for
the granted Lifetime at the time it sent the Registration Request,
even though the granted Lifetime is not known to the mobile node
until the Registration Reply is received. Since the Registration
Request is certainly sent before the home agent begins timing the
registration Lifetime (also based on the granted Lifetime), this
procedure ensures that the mobile node will re-register before the
home agent expires and deletes the registration, in spite of possibly
non-negligible transmission delays for the original Registration
Request and Reply that started the timing of the Lifetime at the
mobile node and its home agent.
3.6.2.3. Registration Request Denied
If the Code field indicates that service is being denied, the mobile
node SHOULD log the error. In certain cases the mobile node may be
able to "repair" the error. These include:
Code 69: (Denied by foreign agent, Lifetime too long)
In this case, the Lifetime field in the Registration Reply will
contain the maximum Lifetime value which that foreign agent is
willing to accept in any Registration Request. The mobile node
MAY attempt to register with this same agent, using a Lifetime
in the Registration Request that MUST be less than or equal to
the value specified in the Reply.
Code 133: (Denied by home agent, Identification mismatch)
In this case, the Identification field in the Registration
Reply will contain a value that allows the mobile node to
synchronize with the home agent, based upon the style of replay
protection in effect (Section 5.7). The mobile node MUST
adjust the parameters it uses to compute the Identification
field based upon the information in the Registration Reply,
before issuing any future Registration Requests.
Code 136: (Denied by home agent, Unknown home agent address)
This code is returned by a home agent when the mobile node is
performing dynamic home agent address resolution as described
in Sections 3.6.1.1 and 3.6.1.2. In this case, the Home Agent
field within the Reply will contain the unicast IP address of
the home agent returning the Reply. The mobile node MAY then
attempt to register with this home agent in future Registration
Requests. In addition, the mobile node SHOULD adjust the
parameters it uses to compute the Identification field based
upon the corresponding field in the Registration Reply, before
issuing any future Registration Requests.
3.6.3. Registration Retransmission
When no Registration Reply has been received within a reasonable
time, another Registration Request MAY be transmitted. When
timestamps are used, a new registration Identification is chosen for
each retransmission; thus it counts as a new registration. When
nonces are used, the unanswered Request is retransmitted unchanged;
thus the retransmission does not count as a new registration (Section
5.7). In this way a retransmission will not require the home agent
to resynchronize with the mobile node by issuing another nonce in the
case in which the original Registration Request (rather than its
Registration Reply) was lost by the network.
The maximum time until a new Registration Request is sent SHOULD be
no greater than the requested Lifetime of the Registration Request.
The minimum value SHOULD be large enough to account for the size of
the messages, twice the round trip time for transmission to the home
agent, and at least an additional 100 milliseconds to allow for
processing the messages before responding. The round trip time for
transmission to the home agent will be at least as large as the time
required to transmit the messages at the link speed of the mobile
node's current point of attachment. Some circuits add another 200
milliseconds of satellite delay in the total round trip time to the
home agent. The minimum time between Registration Requests MUST NOT
be less than 1 second. Each successive retransmission timeout period
SHOULD be at least twice the previous period, as long as that is less
than the maximum as specified above.
3.7. Foreign Agent Considerations
The foreign agent plays a mostly passive role in Mobile IP
registration. It relays Registration Requests between mobile nodes
and home agents, and, when it provides the care-of address,
decapsulates datagrams for delivery to the mobile node. It SHOULD
also send periodic Agent Advertisement messages to advertise its
presence as described in Section 2.3, if not detectable by link-layer
means.
A foreign agent MUST NOT transmit a Registration Request except when
relaying a Registration Request received from a mobile node, to the
mobile node's home agent. A foreign agent MUST NOT transmit a
Registration Reply except when relaying a Registration Reply received
from a mobile node's home agent, or when replying to a Registration
Request received from a mobile node in the case in which the foreign