to a cable fault. It is advisable to repeat
this test to check for a consistent resulting
TDR value, to verify that there is a fault.
A TDR test returns as its result the time
interval, measured in 10 MHz ticks or 100 nsec
units, between the start of TDR test
transmission and the subsequent detection of a
collision or deassertion of carrier. On
successful completion of a TDR test, the result
is stored as the value of an appropriate
instance of an appropriate vendor specific MIB
object, and the OBJECT IDENTIFIER of that
instance is stored in the appropriate instance
of the appropriate test result code object
(thereby indicating where the result has been
stored).
This object identity has been deprecated, since
the ifTestTable in the IF-MIB was deprecated,
and there is no longer a standard mechanism for
initiating an interface test. This left no
standard way of using this object identity."
::= { dot3Tests 1 }
-- Loopback Test
dot3TestLoopBack OBJECT-IDENTITY
STATUS deprecated
DESCRIPTION "******** THIS IDENTITY IS DEPRECATED *******
This test configures the MAC chip and executes
an internal loopback test of memory, data paths,
and the MAC chip logic. This loopback test can
only be executed if the interface is offline.
Once the test has completed, the MAC chip should
be reinitialized for network operation, but it
should remain offline.
If an error occurs during a test, the
appropriate test result object will be set
to indicate a failure. The two OBJECT
IDENTIFIER values dot3ErrorInitError and
dot3ErrorLoopbackError may be used to provided
more information as values for an appropriate
test result code object.
This object identity has been deprecated, since
the ifTestTable in the IF-MIB was deprecated,
and there is no longer a standard mechanism for
initiating an interface test. This left no
standard way of using this object identity."
::= { dot3Tests 2 }
dot3ErrorInitError OBJECT-IDENTITY
STATUS deprecated
DESCRIPTION "******** THIS IDENTITY IS DEPRECATED *******
Couldn’t initialize MAC chip for test.
This object identity has been deprecated, since
the ifTestTable in the IF-MIB was deprecated,
and there is no longer a standard mechanism for
initiating an interface test. This left no
standard way of using this object identity."
::= { dot3Errors 1 }
dot3ErrorLoopbackError OBJECT-IDENTITY
STATUS deprecated
DESCRIPTION "******** THIS IDENTITY IS DEPRECATED *******
Expected data not received (or not received
correctly) in loopback test.
This object identity has been deprecated, since
the ifTestTable in the IF-MIB was deprecated,
and there is no longer a standard mechanism for
initiating an interface test. This left no
standard way of using this object identity."
::= { dot3Errors 2 }
-- { dot3 8 }, the dot3ChipSets tree, is defined in [RFC2666]
-- conformance information
etherConformance OBJECT IDENTIFIER ::= { etherMIB 2 }
etherGroups OBJECT IDENTIFIER ::= { etherConformance 1 }
etherCompliances OBJECT IDENTIFIER ::= { etherConformance 2 }
-- compliance statements
etherCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ********
The compliance statement for managed network
entities which have ethernet-like network
interfaces.
This compliance is deprecated and replaced by
dot3Compliance."
MODULE -- this module
MANDATORY-GROUPS { etherStatsGroup }
GROUP etherCollisionTableGroup
DESCRIPTION "This group is optional. It is appropriate
for all systems which have the necessary
metering. Implementation in such systems is
highly recommended."
::= { etherCompliances 1 }
ether100MbsCompliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ********
The compliance statement for managed network
entities which have 100 Mb/sec ethernet-like
network interfaces.
This compliance is deprecated and replaced by
dot3Compliance."
MODULE -- this module
MANDATORY-GROUPS { etherStats100MbsGroup }
GROUP etherCollisionTableGroup
DESCRIPTION "This group is optional. It is appropriate
for all systems which have the necessary
metering. Implementation in such systems is
highly recommended."
::= { etherCompliances 2 }
dot3Compliance MODULE-COMPLIANCE
STATUS deprecated
DESCRIPTION "******** THIS COMPLIANCE IS DEPRECATED ********
The compliance statement for managed network
entities which have ethernet-like network
interfaces.
This compliance is deprecated and replaced by
dot3Compliance2."
MODULE -- this module
MANDATORY-GROUPS { etherStatsBaseGroup }
GROUP etherDuplexGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating in full-duplex mode.
It is highly recommended for all
ethernet-like network interfaces."
GROUP etherStatsLowSpeedGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating at 10 Mb/s or slower in
half-duplex mode."
GROUP etherStatsHighSpeedGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating at 100 Mb/s or faster."
GROUP etherControlGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces that
support the MAC Control sublayer."
GROUP etherControlPauseGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces that
support the MAC Control PAUSE function."
GROUP etherCollisionTableGroup
DESCRIPTION "This group is optional. It is appropriate
for all ethernet-like network interfaces
which are capable of operating in
half-duplex mode and have the necessary
metering. Implementation in systems with
such interfaces is highly recommended."
::= { etherCompliances 3 }
dot3Compliance2 MODULE-COMPLIANCE
STATUS current
DESCRIPTION "The compliance statement for managed network
entities which have ethernet-like network
interfaces.
Note that compliance with this MIB module
requires compliance with the ifCompliance3
MODULE-COMPLIANCE statement of the IF-MIB
(RFC2863). In addition, compliance with this
MIB module requires compliance with the
mauModIfCompl3 MODULE-COMPLIANCE statement of
the MAU-MIB (RFC3636)."
MODULE -- this module
MANDATORY-GROUPS { etherStatsBaseGroup2 }
GROUP etherDuplexGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating in full-duplex mode.
It is highly recommended for all
ethernet-like network interfaces."
GROUP etherRateControlGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating at speeds faster than
1000 Mb/s. It is highly recommended for all
ethernet-like network interfaces."
GROUP etherStatsLowSpeedGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating at 10 Mb/s or slower in
half-duplex mode."
GROUP etherStatsHighSpeedGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating at 100 Mb/s or faster."
GROUP etherStatsHalfDuplexGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating in half-duplex mode."
GROUP etherHCStatsGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces which are
capable of operating at 10 Gb/s or faster.
It is recommended for all ethernet-like
network interfaces which are capable of
operating at 1000 Mb/s or faster."
GROUP etherControlGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces that
support the MAC Control sublayer."
GROUP etherHCControlGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces that
support the MAC Control sublayer and are
capable of operating at 10 Gb/s or faster."
GROUP etherControlPauseGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces that
support the MAC Control PAUSE function."
GROUP etherHCControlPauseGroup
DESCRIPTION "This group is mandatory for all
ethernet-like network interfaces that
support the MAC Control PAUSE function and
are capable of operating at 10 Gb/s or
faster."
GROUP etherCollisionTableGroup
DESCRIPTION "This group is optional. It is appropriate
for all ethernet-like network interfaces
which are capable of operating in
half-duplex mode and have the necessary
metering. Implementation in systems with
such interfaces is highly recommended."
::= { etherCompliances 4 }
-- units of conformance
etherStatsGroup OBJECT-GROUP
OBJECTS { dot3StatsIndex,
dot3StatsAlignmentErrors,
dot3StatsFCSErrors,
dot3StatsSingleCollisionFrames,
dot3StatsMultipleCollisionFrames,
dot3StatsSQETestErrors,
dot3StatsDeferredTransmissions,
dot3StatsLateCollisions,
dot3StatsExcessiveCollisions,
dot3StatsInternalMacTransmitErrors,
dot3StatsCarrierSenseErrors,
dot3StatsFrameTooLongs,
dot3StatsInternalMacReceiveErrors,
dot3StatsEtherChipSet
}
STATUS deprecated
DESCRIPTION "********* THIS GROUP IS DEPRECATED **********
A collection of objects providing information
applicable to all ethernet-like network
interfaces.
This object group has been deprecated and
replaced by etherStatsBaseGroup and
etherStatsLowSpeedGroup."
::= { etherGroups 1 }
etherCollisionTableGroup OBJECT-GROUP
OBJECTS { dot3CollFrequencies
}
STATUS current
DESCRIPTION "A collection of objects providing a histogram
of packets successfully transmitted after
experiencing exactly N collisions."
::= { etherGroups 2 }
etherStats100MbsGroup OBJECT-GROUP
OBJECTS { dot3StatsIndex,
dot3StatsAlignmentErrors,
dot3StatsFCSErrors,
dot3StatsSingleCollisionFrames,
dot3StatsMultipleCollisionFrames,
dot3StatsDeferredTransmissions,
dot3StatsLateCollisions,
dot3StatsExcessiveCollisions,
dot3StatsInternalMacTransmitErrors,
dot3StatsCarrierSenseErrors,
dot3StatsFrameTooLongs,
dot3StatsInternalMacReceiveErrors,
dot3StatsEtherChipSet,
dot3StatsSymbolErrors
}
STATUS deprecated
DESCRIPTION "********* THIS GROUP IS DEPRECATED **********
A collection of objects providing information
applicable to 100 Mb/sec ethernet-like network
interfaces.
This object group has been deprecated and